Stabilized zirconia ceramics for dental programs

Textile electronics are ideal for novel electronic devices owing to their flexibility, light weight, and wearability. In this work, wearable organic field-effect transistors (OFETs) with all-graphene electrodes, fabricated using hot pressing, are described. Linsitinib First, highly conductive and flexible electrodes consisting of a cotton textile substrate and electrochemically exfoliated graphene (EEG) were prepared via hot pressing. The EEG/textile electrodes exhibited a low sheet resistance of 1.3 Ω sq-1 and high flexibility; these were used as gate electrodes in the wearable OFETs. In addition, spray-coated EEG was also used as the source/drain (S/D) electrodes of the wearable OFETs, which recorded a sheet resistance of 14.8 Ω sq-1 after hot pressing. The wearable OFETs exhibited stable electrical performance, a field-effect mobility of 13.8 cm2 V-1 s-1, and an on-off current ratio of ~103 during 1000 cycles of bending. Consequently, the fabrication method for wearable transistors developed using textiles and hot-pressed graphene electrodes has potential applications in next-generation wearable devices.Lutein is an important antioxidant that quenches free radicals. The stability of lutein and hence compatibility for food fortification is a big challenge to the food industry. Encapsulation can be designed to protect lutein from the adverse environment (air, heat, light, pH). In this study, we determined the impact of mixed biopolymer systems based on bovine and caprine caseins, yeast β-glucan, and maltodextrin as wall systems for microencapsulating lutein dispersed in emulsified lipid carriers by spray drying. The performance of these wall systems at oil/water interfaces is a key factor affecting the encapsulation of lutein. The highest encapsulation efficiency (97.7%) was achieved from the lutein microcapsules prepared with the mixed biopolymer system of caprine αs1-II casein, yeast β-glucan, and maltodextrin. Casein type and storage time affected the stability of lutein. The stability of lutein was the highest (64.57%) in lutein microcapsules prepared with the mixed biopolymer system of caprine αs1-II casein, yeast β-glucan, and maltodextrin, whereas lutein microcapsules prepared with the biopolymer system of bovine casein, yeast β-glucan, and maltodextrin had the lowest (56.01%). The stability of lutein in the lutein microcapsules dramatically decreased during storage time. The antioxidant activity of lutein in the lutein microcapsules was closely associated with the lutein concentration.Welan gum is one of the most promising polymers used in polymer flooding for enhancing oil recovery, due to its excellent temperature resistance and salt-tolerance performance. However, welan gum, as a polymer with higher molecular weight, can be adsorbed and detained in the pore throat of the reservoir, which is characterized by a smaller size. Montmorillonite, a kind of clay mineral with high content in reservoir rocks, has strong adsorption capacity. Therefore, the adsorption behavior of welan gum on montmorillonite, as well as its influencing factors, are studied in this paper. The results show that the adsorption capacity is 2.07 mg/g. The adsorption capacity decreased with the increase in temperature. Both acidic and alkaline conditions reduced the adsorption capacity. The existence of inorganic salt affected the adsorption capacity. In addition, the higher the cation value, the lower the adsorption capacity. The characterization tests showed that the adsorption of welan gum on montmorillonite was characterized by physical adsorption and surface adsorption, indicating that there were no changes in the internal structure of montmorillonite. This study provides feasible methods to reduce the amount of welan gum adsorbed on montmorillonite, which is of great significance for reducing the permeability damage caused by welan gum adsorption and promoting the application of welan gum in polymer flooding for enhancing oil recovery.Microwave curing technology has been widely used in resin and its composite materials. In order to study its effect for curing unsaturated polyester resin (UPR) composites containing calcium carbonate (CaCO3) filler, this paper first investigated the influence of microwave power and microwave irradiation time on the curing characteristics of UPR. Then, CaCO3 particles were added to the UPR to investigate the microwave curing effect of the UPR composites containing the CaCO3. The results showed that microwave irradiation could heat the UPR sample evenly, and rapidly cause the chain growth reaction, thus greatly shortening the curing time. The curing degree and products of the samples after microwave curing were consistent with that of the thermal curing. The addition of CaCO3 particles could increase the heating rate of the UPR composites, which would accelerate the curing rate of the UPR. However, higher microwave power could lead to pore defects inside the UPR composites with higher CaCO3 content, resulting in a lower strength. Thus, the compactness of the samples should be improved by reducing the microwave power and prolonging the microwave treatment time.The objective of this study was to examine the optimal mixing ratio of municipal incinerated bottom ash (MIBA) and PET pellets used as a partial replacement of fine aggregates in the manufacture of cement mortars. As a partial replacement for sand, 15 mortar specimens were prepared by mixing 0%, 10%, 20%, 30%, and 40% municipal incinerated bottom ash (MIBA) (A) and 0%, 10%, and 20% PET pellets (P) in 5 cm × 5 cm × 5 cm cube molds. The cement/aggregate ratio was 13, and the water/cement ratio was 0.5 for all specimens. The results showed that the compressive strength of cement mortars decreased when increasing the amount of MIBA and PET pellets. The mortar specimens with 10% PET pellets achieved the highest compressive strength (49.53 MPa), whereas the mortar specimens with 40% MIBA and 20% PET pellets achieved the lowest compressive strength (24.44 MPa). Based on this finding, replacing 10% and 20% sand in cement mortar with only MIBA or only PET pellets could result in compressive strengths ranging from 46.00 MPa to 49.53 MPa.The connector is an essential component in the solid rocket motor case (SRMC), and its weight and performance can directly affect the blasting performance of SRMC. Considering the lightweight design of these structures, fiber-reinforced composite materials are used for the major components. In this study, the finite element analysis of the SRMC connector was performed. The lay-up design and structure optimum design of the connector were studied. Furthermore, the strain distribution on the composite body was compared with experimental measurements. The results demonstrate that the calculated value of the final preferred solution was within the allowable range, and at least 31% weight loss was achieved, suggesting that the performance of the optimum design was optimized. The comparison between the finite element calculation and the test results suggests that the design was within the allowable range and reasonable.In this paper, we report the synthesis of block and random copolymers of 2-acrylamido-2-methyl-1-propane sulfonic acid (AMPS) and methyl methacrylate (MMA), with different AMPS feed ratios. These solution-processable copolymers with strongly sulfonated acid groups resulted in membranes with tunable ion exchange (IEC) and water absorption capacities. AFM images confirmed the microphase separation of PAMPS-b-PMMA-11 block copolymer membrane, annealed under the appropriate conditions. The resulting copolymers from the random combination of a 11 molar ratio of AMPS and MMA monomers are effective at enhancing the esterification conversion of acetic acid, when compared with a reaction catalyzed by PAMPS-b-PMMA block copolymers and the previously studied catalytic membranes. With the PAMPS-co-PMMA-11 membrane, the esterification reaction using acetic acid achieved 85% isopropyl acetate. These results are closely correlated with the increase in IEC (2.63 mmol H+g-1) and the relationship between weight loss (20.3%) and swelling degree (68%) in 2-propanol.In this paper, the tensile behavior of industrial polypropylene triaxial geogrid with different pre-punched hole diameters was studied by experiment and numerical analysis. The industrial polypropylene sheets with different diameters of circular holes were stretched at elevated temperature and then the tensile properties of triaxial geogrids at room temperature were evaluated. It was found that the pre-punched hole diameter of triaxial geogrid had a very close relationship with the mechanical properties. With the increase of the pre-punched hole diameter, the tensile strength of triaxial geogrid shows a trend of first increasing and then decreasing. Combined with numerical simulation, the optimal pre-punched hole diameter can be accurately obtained, and the distribution law of the width, thickness, stress, and strain of triaxial geogrid can be obtained. Under the condition of a stretching ratio of 3 and node spacing of 3 mm, it was found that the mechanical properties of industrial polypropylene triaxial geogrid was the best when the pre-punched hole diameter was 2.6 mm.This work is a comparative study among three different biocompatible and biodegradable polymers, poly(lactic-co-glycolic acid), poly(ε-caprolactone), and poly(lactic acid), used to produce microparticles for the encapsulation of bevacizumab for drug delivery purposes. All the formulations were produced using the double emulsion water-oil-water evaporation method and characterized in terms of particle mean diameter, particle size distribution, and bevacizumab entrapment efficiency. Bevacizumab cumulative release was taken into consideration to study the dissolution kinetics from the three different polymeric delivery platforms for a period of 50 days at 37 °C in phosphate buffered saline and mathematical models of the drug release kinetic were attempted in order to describe the release phenomena from the different types of the studied microparticles. Finally, cell viability on human endothelial cell line EA.hy926 was studied to define the maximum cytocompatible concentration for each microsystem, registering the mitochondrial functionality through MTS assay.In this article, the effect of plasma treatment of polyethylene powder and glass fibers on the adhesion between polyethylene and glass fibers in composites prepared by rotational molding was studied. In contrast to other processing techniques, such as injection molding, the rotational molding process operates at atmospheric pressure, and no pressure is added to ensure mechanical interlocking. This makes reinforcing the rotomolded product very difficult. Therefore, the formation of chemical bonds is necessary for strong adhesion. Different combinations of untreated polyethylene (UT.PE), plasma-treated polyethylene (PT.PE), untreated and plasma-treated glass fibers were manually mixed and processed by rotational molding. The resulting composites were cut and tested to demonstrate the effect of the treatment on the adhesion between the composite components and on the mechanical properties of the final composites. The results showed that the treatment of both powder and fiber improved the adhesion between the matrix and fibers, thus improving the mechanical properties of the resulting composites compared to those of pure polyethylene samples and composites prepared using untreated components.